Skip to main content

Tri-Cymbal Tops

Wing nuts for cymbal stands are not very expensive, unless 10-15 are lost during the course of a year. This is what happened during the 2017 season of the YS. Maybe because there was an increase of touring which meant a lot of packing and unpacking, or just coincidental.  But the result was the same: time spent on budgeting and then ordering parts.
Another problem was with tightening the wing nuts. Some students felt that it should be threaded on the post until it contacted the sleeve and then add another 4 or 5 turns for good measure. This required more budgeting and ordering to replace the damaged sleeves.
Sometimes when setting up the cymbal, the wing nut would take flight and be forever lost on the floor. For some it was easier to go to the cabinet to get a new one rather than look for the original. Then there was the problem of choosing which threading was needed. Is it 6mm, 8mm, or the older 1/4" x 20 tpi (we had all three)?
I wanted to find a system that would attach onto a stand regardless of the threading or the diameter of the post. The summer after the 2017 season allowed me time to experiment with some different ideas.
The Tri-Cymbal Top

I used a 'Binder Clip' (they come in various sizes, and the 'mini' seemed to be the best choice). I drilled a hole large enough to accommodate an 8mm post in the top center, a Dremel tool was used to cut a half circle on the bottom of the clamp, I put foam on the wire handles and covered them with heat-shrink tubing. It took an hour to make 20 of them.

We now had a system in which one hand could release the clamp while the other placed or removed the cymbal without having to fumble around to catch the wing nut if it escaped. This may not work if the cymbal stand were tilted as used on a drum set, but positioned flat for concert use it was perfect.

I called it a 'Cymbal Top' and then realized it sounded like
Triceratops.
So the Tri-Cymbal Top was born.

























Comments

Post a Comment

Popular posts from this blog

La Caverna del oro

 One of our first backpacking trips in Colorado was in the Sangre de Christo Mountains. One mountain in particular drew our attention. Marble Mountain was the location of a famous story of a Spanish cave of gold. There are many places on the web that tell this story better than I could, suffice it to say that we wanted to locate it and see the iconic 'Maltese Cross' located at it's entrance.  In 1974 after I got out of the Army we invited some friends to join us on this trip. We parked our car at the trailhead in the Wet Mountain Valley and backpacked up Marble Mountain to 12,000 feet. In one of the culverts we found the entrance to the cave. Maltese Cross at the Caverna del oro It turned out to be a real thing. The large red cross was still visible after 400 yrs. According to legend the Spanish put it there in the 1600's. I did have the courage to crawl into it but only a few feet. After about 10 feet there is a vertical shaft that drops about 750 feet!  The Cross is v...

The Amadinda

  The Amadinda is an African xylophone originally made from slabs of wood or even large sticks, with or without gourds for resonators. There was no reason for this project other than to see if I could make a simple mallet instrument. The box was made from plywood (which also acted as the resonators) and the bars were made from maple.  Since this was to be a true xylophone, the bars were all of equal width. Tuning was done by cutting the bars to different lengths and removing material from the bottom. Using a router I created a sort of 'stepped pyramid' instead of the traditional arc cut found on marimba or xylophone bars.  Cutting the underside is not only for tuning but it focuses the pitch and creates the characteristic overtones of the instrument. Since I wanted to play this with other 'Western' instruments, I chose to use a pentatonic scale of 2 2/5 octaves (C#,D#,F#,G#,A#,C#,D#,F#,G#,A#,C#,D#). Two people sit on either side of the instrument and strike the ends of ...

Zenith tubes, Analema, and Crossed Trapezes

The Zenith Sun  A common characteristic in Mesoamerica is the observance of the sun's zenith passage. This happens when the sun passes directly overhead at noon. It appears twice a year around late April and mid-August. Many ancient sites from Mexico east to the Yucatan seem to have systems built into their architecture to show this phenomenon. In the Mayan city of Kabah there is a cylindrical stone marker placed vertically in a plaza that seems to act as a gnomon that will produce a shadow every day except during the time of the sun's zenith position when the shadow disappears. In Monte Alban, Oaxaca and Xochicalco, Mexico the devices are more sophisticated. These have Zenith tubes in buildings that direct the rays of the sun down their passages to produce a circle of light onto the floor of a darkened chamber.  Looking up through the zenith tube Sun light on the floor of Xochicalco zenith tube. The Mixtec A-O glyph The Mixtec A-O glyph was their symbol for 'year'. The...