Skip to main content

More Rattles- Gourds

 My original thought of using Coyote gourds fell through so I cheated and ordered some from Amazon. I received 4 'Cannonball' gourds last week. They are called 'Cannonball' gourds because the shape and size resembles cannonballs from the Civil War era. Although they were dried, they still had to be drilled (for handles) and the center pulp removed. Drilling was easy, I started with a 1/16" bit and worked my way up to 5/8". The sizing of the bits was critical, starting with too large of a bit would crack the shell of the gourd.

Drilling the holes for handles


The hard part started when I tried to remove the seeds and pulp from the inside. My wife and I shared some quality time together removing everything from the 4 gourds while watching reruns of The Twilight Zone. It wasn't until later that night when I read that the insides usually have mold in them and the process should be done outdoors with a mask (OOPS!) So I put everything in the garage for the night and vacuumed the entire house before going to bed. Using screwdrivers got rid of the majority of stuff but there was still a layer of soft pulp left on the insides. For the final cleaning I placed sheet metal screws and square nuts from bolts, shaking the gourd in every conceivable pattern/removing the nuts and screws/ blowing the dust out with my compressor. I repeated this pattern for 3 hours outside and left them in the sun for 2 days. That worked.
The next step was to experiment with different materials to put in the gourds. This started my 'Goldylocks principle', the metal nuts were loud but produced a dead sound, popcorn gave a higher pitch but was too soft, wooden beads gave a loud sound and a sharper sound, beans were too muted, bone beads were similar to the wooden beads with a sharper sound. Since I was making 4 rattles for this project I decided to mix them up.
No.1 has wooden beads only.
No. 2 has wooden beads and a small amount of popcorn.
No.3 has bone beads.
No.4 has wooden and bone beads.

Choosing that proper rattle sound


I need to get more wooden and bone beads and then the next step will be to install the handles.







Labels:

Comments

Post a Comment

Popular posts from this blog

The Amadinda

  The Amadinda is an African xylophone originally made from slabs of wood or even large sticks, with or without gourds for resonators. There was no reason for this project other than to see if I could make a simple mallet instrument. The box was made from plywood (which also acted as the resonators) and the bars were made from maple.  Since this was to be a true xylophone, the bars were all of equal width. Tuning was done by cutting the bars to different lengths and removing material from the bottom. Using a router I created a sort of 'stepped pyramid' instead of the traditional arc cut found on marimba or xylophone bars.  Cutting the underside is not only for tuning but it focuses the pitch and creates the characteristic overtones of the instrument. Since I wanted to play this with other 'Western' instruments, I chose to use a pentatonic scale of 2 2/5 octaves (C#,D#,F#,G#,A#,C#,D#,F#,G#,A#,C#,D#). Two people sit on either side of the instrument and strike the ends of ...
3 comments
Read more

La Caverna del oro

 One of our first backpacking trips in Colorado was in the Sangre de Christo Mountains. One mountain in particular drew our attention. Marble Mountain was the location of a famous story of a Spanish cave of gold. There are many places on the web that tell this story better than I could, suffice it to say that we wanted to locate it and see the iconic 'Maltese Cross' located at it's entrance.  In 1974 after I got out of the Army we invited some friends to join us on this trip. We parked our car at the trailhead in the Wet Mountain Valley and backpacked up Marble Mountain to 12,000 feet. In one of the culverts we found the entrance to the cave. Maltese Cross at the Caverna del oro It turned out to be a real thing. The large red cross was still visible after 400 yrs. According to legend the Spanish put it there in the 1600's. I did have the courage to crawl into it but only a few feet. After about 10 feet there is a vertical shaft that drops about 750 feet!  The Cross is v...
3 comments
Read more

Matte Black

 I just realized that this sounds like a 'James Bond' type spy thriller. Actually it involves my attempts to produce a non-reflective finish for so many of my aluminum projects. Powder coating and anodizing are the typical processes to produce this finish but they are expensive or require car battery chargers and caustic chemicals for the DIYers.  I've tried a flat black paint using etching preps etc. but they all resulted in the paint chipping off quickly when tossed around and hitting other things in an accessory case. Since I use a 2 part epoxy to connect the parts of the Nickster together with perfect results, I thought about using this as a bass coat for the paint (see my Nickster Commemorative post). This result had promise but the finish became glossy even though I used the matte black paint in the mixture.  I came up with this idea from an accident. After the epoxy/paint mixture experiment I left some of the mixture out and some of the paint had dripped on the mix...
2 comments
Read more